|
Jeep Friends Forum This is a forum for jeep friends to hang out. For more formal atmosphere hop over to the Technical Forum |
|
Thread Tools | Rate Thread | Display Modes |
#1
|
|||
|
|||
Drive shaft lengths for Atlas II on 97 TJ ????
Drive shaft lengths for Atlas II on 97 TJ ????
Hi Folks, I have decided to upgrade my NV231 with Tera4Low to the Atlas II and I know I will need some drive shaft work. van anyone give me any clues to the length of the front and rear drive shafts I will need? I already have Tom Woods CV shafts and I can get these reworked here in Kentucky but I am a bit immobile at the time. What I would like to do is have a friend drop my shafts for me now and send them out so in two weeks when my new T/case arrives I will be ready to put it in. My Jeep isn't built up as much as most of yours are but here are what I thing the pertinent specs would be. 1997 TJ, 4.0L, 5 speed, 2 inch spring lift, Tera adjustable control arms, HD short conversion, BellyUp, Super D35 with Ox Locker rear, D30 up front with ARB. Did I leave anything important out? Has anyone done an Atlas II in a Jeep like mine? and who wouldn't mind getting me the front and rear drive shaft lengths? Thanks in advance. Frank |
#2
|
|||
|
|||
<BLOCKQUOTE><font size="-1">quote:</font><HR>Originally posted by Daless2:
Drive shaft lengths for Atlas II on 97 TJ ???? Hi Folks, I have decided to upgrade my NV231 with Tera4Low to the Atlas II and I know I will need some drive shaft work. Can anyone give me any clues to the length of the front and rear drive shafts I will need? I already have Tom Woods CV shafts and I can get these reworked here in Kentucky but I am a bit immobile at the time. What I would like to do is have a friend drop my shafts for me now and send them out so in two weeks when my new T/case arrives I will be ready to put it in. My Jeep isn't built up as much as most of yours are but here are what I thing the pertinent specs would be. 1997 TJ, 4.0L, 5 speed, 2 inch spring lift, Tera adjustable control arms, HD short conversion, BellyUp, Super D35 with Ox Locker rear, D30 up front with ARB. Did I leave anything important out? Has anyone done an Atlas II in a Jeep like mine? and who wouldn't mind getting me the front and rear drive shaft lengths? Thanks in advance. Frank[/quote] |
#3
|
|||
|
|||
My DS is 5" longer in the rear and a couple shorter in the front.
I have the D44 and the 30 (currently) HTH Humpty Dumpty |
#4
|
|||
|
|||
Hi Seth, thanks for replying.
The rear DS is five inches longer. Is that from the stock drive shaft or an already converted SYE? Any chance I can ask a favor of you to actually measure both shafts from yoke center to yoke center. I would greatly appreciate this if you could. If not, no problem. Thanks, Frank |
#5
|
|||
|
|||
#6
|
|||
|
|||
Thanks Seth, that would be a big help. Could you also tell me what transmision you have and how much lift you're running?
Once again, Thank You. Frank |
#7
|
|||
|
|||
How about a bizarre comparison Frank? Mine are 23" for the rear and 37 1/2" for the front.
You are just another ride in the amusement park of my mind.
__________________
I am Savvy. |
Bookmarks |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Decent Drive shaft shop somewhere around L.A.? | speaceman | Jeep Friends Forum | 14 | 07-03-2007 11:12 PM |
Rear drive shaft q.. | pcoplin | Technical Forum | 0 | 04-28-2004 03:51 PM |
Drive shaft shop inn SOCAL | Scott Hill | Technical Forum | 9 | 12-22-2002 10:11 AM |
Removed rear drive shaft, why no leak? | KY-Jeep | Technical Forum | 9 | 08-17-2002 06:19 PM |
Driving w/o rear drive shaft - need to know | Ace! | Technical Forum | 11 | 09-21-2001 04:47 PM |